Xaircraft Super X Uživatelský manuál

User Manual V1.9 （for SuperX Firmware v1.08 ）

7 ©2013 XAircraft All Rights Reserved. SuperX Flight Mode Flight Mode IO Functions Explanation Manual Mode M No Auto Horizontal ability. Not recomme

8 ©2013 XAircraft All Rights Reserved. Solid Red After SuperX powered on, system initialization failed. Normally, initialization process within 10 s

9 ©2013 XAircraft All Rights Reserved. Installation Install SuperX Modules Connect Flight Controller, GPS Module, LED Module to IO Module as diagra

10 ©2013 XAircraft All Rights Reserved. Connection to Receiver HITEC，FUTABA，（ WFLY）Wiring Restore factory settings of the radio, then do the sett

11 ©2013 XAircraft All Rights Reserved. Power Supply SuperX use JST-3Pin signal (Futaba) power wire, one end connected to lipo battery an

12 ©2013 XAircraft All Rights Reserved. Copter Types SuperX Supports Different firmware versions can support different kinds of copter: Firmware Cop

13 ©2013 XAircraft All Rights Reserved. Notice: in the following diagram, the arrow direction means to rotation direction of motor and blade. When y

14 ©2013 XAircraft All Rights Reserved. Calibration Mode Compass Calibration 1. Fast altering Flight Mode switch between modes. When LED flashing r

15 ©2013 XAircraft All Rights Reserved. 6. Vertical Calibration B: Copter side up, and then revolve the copter slowly. When LED shows solid green c

16 ©2013 XAircraft All Rights Reserved. 2. Push both sticks to top right as diagram shows, the LED show triple green flashing. 3. Keep both stick

目 录 XAircraft SuperX Overview ...

17 ©2013 XAircraft All Rights Reserved. Auto Take-off Push throttle to neutral point immediately after motors started, SuperX will auto take -off an

18 ©2013 XAircraft All Rights Reserved. 2. RC Gain: If G input on IO module is connected, you can use a knob on radio to adjust roll and pitch att

19 ©2013 XAircraft All Rights Reserved. 1. Return to home and landing(tail in): copter turns its tail towards home (H) and then lifts up to 15m he

20 ©2013 XAircraft All Rights Reserved. About Home Position 1. If GPS has good signals before take-off, the home position is the place where motors

21 ©2013 XAircraft All Rights Reserved. Gimbal When SuperX works for less than 6 rotors, M7 and M8 output ports of IO module can output gimbal stabi

22 ©2013 XAircraft All Rights Reserved. OSD Module  Channel: choose one of channels as video input.  System: choose corresponding video syste

23 ©2013 XAircraft All Rights Reserved. OSD Diagram on Screen 1. Number of Satellite: The number of satellite that GPS has picked up. There are 10

24 ©2013 XAircraft All Rights Reserved. Firmware Upgrade and Configuration Software Update  Upgrade Firmware 1. Connect SuperX to Computer. 2. C

25 ©2013 XAircraft All Rights Reserved. 2. Copy SuperX. exe to root of removable disk ”SuperX ”, and then cover the old version. 3. Open configur

26 ©2013 XAircraft All Rights Reserved. XAircraft SuperX After-sale 1. Warranty Items 1) XAircraft provides a manufacturer's warranty on elec

Flight Controller Information and Language ... 25 XAircraft SuperX After-sale .

27 ©2013 XAircraft All Rights Reserved. d) Your contact information. 2) XAircraft or global distributor/seller strictly follows the warranty items

28 ©2013 XAircraft All Rights Reserved. [email protected] http://www.xaircraft.com XAircraft has the final power o

1 ©2013 XAircraft All Rights Reserved. DISCLAIMER OF LIABILITY 1. Using XAircraft products within the limits permitted by local laws and regulation

2 ©2013 XAircraft All Rights Reserved. XAircraft SuperX Overview XAircraft SuperX is designed for multicopter, support 2 to 8 rotors. Products Spe

3 ©2013 XAircraft All Rights Reserved. GPS Module  Built-in Compass.  Provides GPS position and heading data for Flight Controller. Supe

4 ©2013 XAircraft All Rights Reserved. Products Electrical Features Weight Size Flight Controller Input Voltage: 5.7V ~ 6.0V Power consumption: 

5 ©2013 XAircraft All Rights Reserved. IO Module Input Ports IO Ports Functions B Battery, use Lipo battery (3S~6S, 11.1V~28V) supply power for Supe

6 ©2013 XAircraft All Rights Reserved. Below is the connection between IO V2 and SBUS Receiver.